8B-107 Air Bag System:
3) Check that there is no open, short or damage in
special tools (deployment harness (A), adapter cable
(B) and adapter cable (C)). If any faulty is found, do
not use it and be sure to use new special tool.
Special tool
(A): 09932-75030
(B): 09932–76510
(C): 09932–78332
NOTE
If faulty of adapter cable (C) is found, replace
it with spare connector (D).
For special tool (C) spare connector
Special tool
(D): 09932–75410
4) Short two deployment harness leads (1) together by
fully seating one banana plug into the other.
WARNING
!
Deployment harness (A) shall remain shorted
and not be connected to 12 volts vehicle
battery till you are ready to deploy air bag
module or activate seat belt pretensioner.
5) Remove air bag (inflator) module(s) or seat belt
pretensioner(s) from vehicle referring to “Driver Air
Bag (Inflator) Module Removal and Installation”,
“Passenger Air Bag (Inflator) Module Removal and
Installation”, “Side Air Bag (Inflator) Module Removal
and Installation” or “Front Seat Belt Removal and
Installation in Section 8A”.
WARNING
!
• For handing and storage of live air bag
(inflator) module, select place where
ambient temperature below 65
°
C (150
°
F),
without high humidity and away from
electric noise.
• Always carry live air bag (inflator) module
with trim cover away from you.
• When storing live air bag (inflator) module
or when leaving live air bag (inflator)
module unattended on bench or other
surface, always face trim cover up and
away from surface. As the live passenger
air bag (inflator) module must be placed
with its bag (trim cover) facing up, place it
on the workbench with a slit (1) or use the
workbench vise (2) to hold it securely at its
lower mounting bracket (3). It is also
prohibited to place anything on top of the
trim cover and stack air bag (inflator)
modules. This is necessary so that free
space is provided to allow air bag (inflator)
module to expand in the unlikely event of
accidental deployment.
Failure to follow procedures may result in
personal injury.
I3RH0A820077-01
1
I3RH0A820078-02
Содержание Liana RH413
