manualshive.com logo in svg

Renesas SH7616, Руководство по оборудованию

Renesas SH7616 - мощный микроконтроллер, предназначенный для широкого спектра приложений. Для бесплатного скачивания подробного "Hardware Manual" по этому продукту, посетите manualshive.com. Этот "manual" поможет вам максимально эффективно использовать все возможности микроконтроллера в вашем проекте.

Поделиться
Скачать
background image

Section 10   Ethernet Controller Direct Memory Access Controller (E-DMAC)

Rev. 2.00  Mar 09, 2006  page 460 of 906
REJ09B0292-0200

1), this indicates a buffer for which reception has not yet been performed.  If a frame receive error
occurs in the first descriptor part where the RACT bit = 1 in the figure, reception is halted
immediately and a status write-back to the descriptor is performed.

If error interrupts are enabled in the EtherC/E-DMAC status interrupt permission register
(EESIPR), an interrupt is generated immediately after the write-back.  If there is a new frame
receive request, reception is continued from the buffer after that in which the error occurred.

0  0

0  0

0  0

0  0

1  0

1  0

1  0

1  0

1  1

1  0

0  0

0  0

0  0

0  0

0  0

0  0

0  0

0  0

E-DMAC

Inactivates RACT and writes RFE, RFS

Descriptor read

Write-back 

Descriptors

Buffer

Received data

Unreceived data

Receive error occurrence

:
:
:
:
:

Start of frame

New frame reception 
continues from this buffer

RACT

RDLE

RFP1

RFP0

Figure 10.7   E-DMAC Operation after Receive Error

Содержание SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7616

TC-Helicon PERFORM-VK Quick Start Manual preview
PERFORM-VK
Бренд: TC-Helicon Страницы: 2
Commell LS-570 User Manual preview
LS-570
Бренд: Commell Страницы: 58
MiLAN E-MCC-1600 Install Manual preview
E-MCC-1600
Бренд: MiLAN Страницы: 1
Symantec PacketShaper PS-S200 Quick Start Manual preview
PacketShaper PS-S200
Бренд: Symantec Страницы: 2
Fostex DE-1 Service Manual preview
DE-1
Бренд: Fostex Страницы: 20
RuggedCom RUGGEDMAX WIN7000 Installation Manual preview
RUGGEDMAX WIN7000
Бренд: RuggedCom Страницы: 42
Keithley PDISO-8 User Manual preview
PDISO-8
Бренд: Keithley Страницы: 71
Aqua Computer Aquaduct 360 XT Operating And Assembly Manual preview
Aquaduct 360 XT
Бренд: Aqua Computer Страницы: 28
ENERMAX ELC-LTTR240-TBP User Manual preview
ELC-LTTR240-TBP
Бренд: ENERMAX Страницы: 16
ebm-papst R3G175-AF01-02 Operating Instructions Manual preview
R3G175-AF01-02
Бренд: ebm-papst Страницы: 11
Paradyne Hotwire 8775 MSDSL Installation Instructions Manual preview
Hotwire 8775 MSDSL
Бренд: Paradyne Страницы: 10
Arbor Technology Em104P-i2904 Quick Installation Manual preview
Em104P-i2904
Бренд: Arbor Technology Страницы: 8
Supero SAS 846 TQ User Manual preview
SAS 846 TQ
Бренд: Supero Страницы: 16
Intel 640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU User Manual preview
640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU
Бренд: Intel Страницы: 105
Idis DR-6316PS-S Quick Manual preview
DR-6316PS-S
Бренд: Idis Страницы: 16
ZIMO MXULFA Instruction Manual preview
MXULFA
Бренд: ZIMO Страницы: 13
B&B Electronics 232PCC User Manual preview
232PCC
Бренд: B&B Electronics Страницы: 17
Aaeon FWS-7150 Manual preview
FWS-7150
Бренд: Aaeon Страницы: 57

Бренды по названию

Популярные бренды

Загрузить еще бренды