manualshive.com logo in svg

Renesas SH7616, Руководство по оборудованию

Renesas SH7616 - мощный микроконтроллер, предназначенный для широкого спектра приложений. Для бесплатного скачивания подробного "Hardware Manual" по этому продукту, посетите manualshive.com. Этот "manual" поможет вам максимально эффективно использовать все возможности микроконтроллера в вашем проекте.

Поделиться
Скачать
background image

Section 14   Serial Communication Interface with FIFO (SCIF)

Rev. 2.00  Mar 09, 2006  page 601 of 906

REJ09B0292-0200

•

 

Serial Data Reception (Asynchronous Mode)
Figure 14.8 shows a sample flowchart for serial reception.
Use the following procedure for serial data reception after enabling the SCIF for reception.

1.  PFC initialization: Set the RxD pin, and 

the SCK pin if necessary, with the PFC.

2.  Receive error handling and break 

detection: Read ER, BRK, FER, PER, 
and DR in SC1SSR, and ORER in 
SC2SSR, to check whether a receive 
error has occurred.

 

If a receive error has occurred, read the 
ER, BRK, FER, PER, and DR flags in 
SC1SSR and the ORER flag in SC2SSR 
to identify the error. After performing the 
appropriate error handling, ensure that 
the ORER, BRK, DR, and ER bits are all 
cleared to 0. Reception cannot be 
resumed if the ORER bit is set to 1. The 
setting of the EI bit in SC2SSR 
determines whether reception is 
continued or halted when any of 
PER3–0 or FER3–0 is set to 1.

 

In the case of a framing error, a break 
can be detected by reading the value of 
the RxD pin.

3.  SCIF status check and receive data 
 

read: Read the serial status 1 register 
(SC1SSR) and check that RDF = 1, then 
read receive data from the receive FIFO 
data register (SCFRDR) and clear the 
RDF bit to 0. Transition of the RDF bit 
from 0 to 1 can also be identified by 
means of an RXI interrupt.

4.  Serial reception continuation procedure: 

To continue serial reception, read at 
least the receive trigger set number of 
data bytes from SCFRDR, and write 0 to 
the RDF flag after reading 1 from it. The 
number of receive data bytes in 
SCFRDR can be ascertained by reading 
the lower bits of the FIFO data count 
register (SCFDR). (The RDF bit is 
cleared automatically when the DMAC is 
activated by an RXI interrupt and the 
SCFRDR value is read.)

Initialization

Start of reception

Read ER, BRK, FER, PER,

and DR bits in SC1SSR, and

ORER bit in SC2SSR

ER 

∨

 BRK 

∨

 

FER 

∨

 PER 

∨

 

DR 

∨

   

ORER = 1?

Error handling

Read RDF flag in SC1SSR

RDF = 1?

Read receive data

from SCFRDR, and clear 

RDF flag to 0 in SC1SSR

All data received?

Clear RE bit to 0 in SCSCR

End of reception

Yes

No

Yes

No

No

Yes

1

2

3

4

Figure 14.8   Sample Serial Reception Flowchart (1)

Содержание SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7616

Dave Embedded Systems ARM Cortex-A9 MPCore Quick Start Manual preview
ARM Cortex-A9 MPCore
Бренд: Dave Embedded Systems Страницы: 67
Lattice Semiconductor ECP5 Versa Quick Start Manual preview
ECP5 Versa
Бренд: Lattice Semiconductor Страницы: 15
Queclink GV600 Series Instruction Manual preview
GV600 Series
Бренд: Queclink Страницы: 9
Belkin F5D9001 Series Manual preview
F5D9001 Series
Бренд: Belkin Страницы: 72
Measurement Computing PC-CARD DAS16 User Manual preview
PC-CARD DAS16
Бренд: Measurement Computing Страницы: 27
Velopex Extra-X Quick Start Manual preview
Extra-X
Бренд: Velopex Страницы: 7
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Бренд: Tandberg Data Страницы: 6
Lanner NCA-1525 User Manual preview
NCA-1525
Бренд: Lanner Страницы: 78
Z3 Technology SBE264-10-RPS User Instructions preview
SBE264-10-RPS
Бренд: Z3 Technology Страницы: 87
Aaeon SBC-657B Manual preview
SBC-657B
Бренд: Aaeon Страницы: 61
Supero SAS 846 TQ User Manual preview
SAS 846 TQ
Бренд: Supero Страницы: 16
Commell FS-A79 User Manual preview
FS-A79
Бренд: Commell Страницы: 36
Dataprobe iBoot Instruction Manual preview
iBoot
Бренд: Dataprobe Страницы: 16
ICP DAS USA I-87K Series User Manual preview
I-87K Series
Бренд: ICP DAS USA Страницы: 31
Microtek MiniLink Operation Manual preview
MiniLink
Бренд: Microtek Страницы: 25
Sony Ericsson Developer's Board Manual preview
Developer's Board
Бренд: Sony Ericsson Страницы: 28
uneron eSOM3735z Quick Start Manual preview
eSOM3735z
Бренд: uneron Страницы: 13
DTS XD10P Installation And Operation Manual preview
XD10P
Бренд: DTS Страницы: 94

Бренды по названию

Популярные бренды

Загрузить еще бренды