Renesas SH7616 Скачать руководство пользователя страница 269 | Manualshive

Страница: 269 / 935

background image

Section 6 User Break Controller (UBC)

Rev. 2.00 Mar 09, 2006 page 243 of 906

REJ09B0292-0200

4. BRSR, BRDR, and BRFR have a four-queue structure. When the stored address is read in a PC

trace, the read is performed from the head of the queue. Reads should be performed in the
order BRFR, BRSR, BRDR. After BRDR is read, the queue shifts by one. Use longword
access to read BRSR and BRDR.

6.3.8

Examples of Use

CPU Instruction Fetch Cycle Break Condition Settings

A.

Register settings: BARA = H'00000404 / BAMRA = H'00000000 / BBRA = H'0054

BARB = H'00003080 / BAMRB = H'0000007F / BBRB = H'0054
BARC = H'00008010 / BAMRC = H'00000006 / BBRC = H'0054
BDRC = H'00000000 / BDMRC = H'00000000
BARD =H'0000FF04 / BAMRD = H'00000000 / BBRD = H'0054
BDRD = H'00000000 / BDMRD = H'00000000
BRCR = H'04000400

Set conditions:

All channels independent

Channel A: Address: H'00000404; address mask: H'00000000

Bus cycle: CPU, instruction fetch (post-execution),

read (operand size not included in conditions)

Channel B: Address: H'00003080; address mask: H'0000007F

Bus cycle: CPU, instruction fetch (pre-execution),

read (operand size not included in conditions)

Channel C: Address: H'00008010; address mask: H'00000006

Data:

H'00000000; data mask: H'00000000

Bus cycle: CPU, instruction fetch (post-execution),

read (operand size not included in conditions)

Channel D: Address: H'0000FF04; address mask: H'00000000

Data:

H'00000000; data mask: H'00000000

Bus cycle: CPU, instruction fetch (pre-execution),

read (operand size not included in conditions)

A user break interrupt is generated after execution of the instruction at address H'00000404,
before execution of instructions at addresses H'00003080 to H'000030FF, after execution of
instructions at addresses H'00008010 to H'00008016, or before execution of the instruction at
address H'0000FF04.

«
...
267
268
269
270
271
...
»

Содержание SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7616

Бренд: XDS Страницы: 99

Бренд: Alacritech Страницы: 20

eXtremeRAID 1100

Бренд: Mylex Страницы: 74

Бренд: Measurement Computing Страницы: 27

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 3

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 4

Бренд: Advantech Страницы: 36

Бренд: Eaton Страницы: 14

Enterasys Matrix 2G4082-25

Бренд: Enterasys Страницы: 58

Бренд: Pressalit Care Страницы: 31

Бренд: Loopcomm Страницы: 2

500 - DATASHEET REV 003

Бренд: Intel Страницы: 67

Tamar FCSAS102800

Бренд: Bridgeworks Страницы: 56

Бренд: IBM Страницы: 74

GigaVUE H TA100-CXP

Бренд: Gigamon Страницы: 115

Sporlan Division SCS-PB Series

Бренд: Parker Страницы: 10

Бренд: Radio Shack Страницы: 154

Бренд: NI Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды