manualshive.com logo in svg

Renesas SH7616, Руководство по оборудованию

Renesas SH7616 - мощный микроконтроллер, предназначенный для широкого спектра приложений. Для бесплатного скачивания подробного "Hardware Manual" по этому продукту, посетите manualshive.com. Этот "manual" поможет вам максимально эффективно использовать все возможности микроконтроллера в вашем проекте.

Поделиться
Скачать
background image

Section 13   Watchdog Timer (WDT)

Rev. 2.00  Mar 09, 2006  page 554 of 906
REJ09B0292-0200

13.4

Usage Notes

13.4.1

Contention between WTCNT Write and Increment

If a count-up pulse is generated at the timing shown in figure 13.8 during a watchdog timer
counter (WTCNT) write cycle, the write takes priority and the timer counter is not incremented
(figure 13.8).

WTCNT address

Address

Internal write

signal

WTCNT input

clock

WTCNT

Counter write data

N

M

Figure 13.8   Contention between WTCNT Write and Increment

13.4.2

Changing CKS2 to CKS0 Bit Values

If the values of bits CKS2 to CKS0 are altered while the WDT is running, the count may
increment incorrectly. Always stop the watchdog timer (by clearing the TME bit to 0) before
changing the values of bits CKS2 to CKS0.

13.4.3

Switching between Watchdog Timer Mode and Interval Timer Mode

The WDT may not operate correctly if it is switched between watchdog timer mode and interval
timer mode while it is running.

To ensure correct operation, always stop the watchdog timer (by clearing the TME bit to 0) before
switching between watchdog timer mode and interval timer mode.

Содержание SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7616

Aastra CNX Product Brief preview
CNX
Бренд: Aastra Страницы: 2
Quantum Scalar 50 Upgrade Instructions preview
Scalar 50
Бренд: Quantum Страницы: 20
Supero Supero SAS-826A User Manual preview
Supero SAS-826A
Бренд: Supero Страницы: 16
Jaycar Electronics Duinotech Lilypad Plus XC3920 Quick Start preview
Duinotech Lilypad Plus XC3920
Бренд: Jaycar Electronics Страницы: 2
National Instruments NI-9206 Getting Started preview
NI-9206
Бренд: National Instruments Страницы: 8
Marani LPP-440A User Manual preview
LPP-440A
Бренд: Marani Страницы: 39
ICOP Technology Vortex86SX VSX-6100 User Manual preview
Vortex86SX VSX-6100
Бренд: ICOP Technology Страницы: 50
IMC Networks Wireless Outdoor Bridge XI-1500-IH Quick Installation Manual preview
Wireless Outdoor Bridge XI-1500-IH
Бренд: IMC Networks Страницы: 13
Alphacool NexXxoS GPX-N 1070-M08 Instruction Manual preview
NexXxoS GPX-N 1070-M08
Бренд: Alphacool Страницы: 4
BSS Audio Soundweb 9088ii DSP System    Brochure & Specs preview
Soundweb 9088ii DSP System   
Бренд: BSS Audio Страницы: 2
TECO e-chill 1 Instruction Manual preview
e-chill 1
Бренд: TECO Страницы: 24
IBA ibaBM-FOX-i-3o-D Manual preview
ibaBM-FOX-i-3o-D
Бренд: IBA Страницы: 13
Asus AAEON BOXER-8256AI User Manual preview
AAEON BOXER-8256AI
Бренд: Asus Страницы: 55
Asus AAM6020VI-T4 User Manual preview
AAM6020VI-T4
Бренд: Asus Страницы: 40
Asus Aaeon ICS-6280 User Manual preview
Aaeon ICS-6280
Бренд: Asus Страницы: 75
Asus WL-HDD2.5 Quick Manual preview
WL-HDD2.5
Бренд: Asus Страницы: 98
Asus AAEON FWS-7541 User Manual preview
AAEON FWS-7541
Бренд: Asus Страницы: 80
Asus Aaeon FWS-2273 User Manual preview
Aaeon FWS-2273
Бренд: Asus Страницы: 101

Бренды по названию

Популярные бренды

Загрузить еще бренды