manualshive.com logo in svg

Renesas SH7616, Руководство по оборудованию

Renesas SH7616 - мощный микроконтроллер, предназначенный для широкого спектра приложений. Для бесплатного скачивания подробного "Hardware Manual" по этому продукту, посетите manualshive.com. Этот "manual" поможет вам максимально эффективно использовать все возможности микроконтроллера в вашем проекте.

Поделиться
Скачать
background image

Section 14   Serial Communication Interface with FIFO (SCIF)

Rev. 2.00  Mar 09, 2006  page 596 of 906
REJ09B0292-0200

Clock: 

Either an internal clock generated by the built-in baud rate generator or an external clock

input at the SCK pin can be selected as the SCI’s serial clock, according to the setting of the C/

A

bit in SCSMR and the CKE1 and CKE0 bits in SCSCR. For details of SCIF clock source
selection, see table 14.9.

When an external clock is input at the SCK pin, the input clock frequency should be 16, 8, or 4
times the bit rate used.

When the SCIF is operated on an internal clock, the clock can be output from the SCK pin. The
frequency of the clock output in this case is 16, 8, or 4 times the bit rate.

Data Transmit/Receive Operations

•

 

SCIF Initialization (Asynchronous Mode)
Before transmitting and receiving data, it is necessary to clear the TE and RE bits to 0 in
SCSCR, then initialize the SCIF as described below.
When the operating mode, communication format, etc., is changed, the TE and RE bits must be
cleared to 0 before making the change using the following procedure. When the TE bit is
cleared to 0, the transmit shift register (SCTSR) is initialized. Note that clearing the TE and RE
bits to 0 does not change the contents of the serial status 1 register (SC1SSR), the transmit
FIFO data register (SCFTDR), or the receive FIFO data register (SCFRDR). The TE bit should
not be cleared to 0 until all transmit data has been transmitted and the TEND flag has been set
in SC1SSR. It is possible to clear the TE bit to 0 during transmission, but the data being
transmitted will go to the high-impedance state after TE is cleared. Also, before starting
transmission by setting TE again, the TFRST bit should first be set to 1 in SCFCR to reset
SCFTDR.
When an external clock is used the clock should not be stopped during operation, including
initialization, since operation will be unreliable in this case.
Figure 14.4 shows a sample SCIF initialization flowchart.

Содержание SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7616

IEI Technology PCIE-Q470 Quick Installation Manual preview
PCIE-Q470
Бренд: IEI Technology Страницы: 19
IEI Technology KINO-DH420 User Manual preview
KINO-DH420
Бренд: IEI Technology Страницы: 87
IEI Technology HPE-4S2 Quick Installation Manual preview
HPE-4S2
Бренд: IEI Technology Страницы: 3
Paradyne COMSPHERE 3800 Series Release Note preview
COMSPHERE 3800 Series
Бренд: Paradyne Страницы: 88
Paradyne COMSPHERE 3800PLUS Supplementary Manual preview
COMSPHERE 3800PLUS
Бренд: Paradyne Страницы: 5
SIIG NN-EC2812-S1 Quick Installation Manual preview
NN-EC2812-S1
Бренд: SIIG Страницы: 12
Delta Electronics Through Hole Power Inductors 1411 Product Specifications preview
Through Hole Power Inductors 1411
Бренд: Delta Electronics Страницы: 1
Caen A 1735 Technical Information Manual preview
A 1735
Бренд: Caen Страницы: 14
ETL TeleCLIENT TC7730 Series User Manual preview
TeleCLIENT TC7730 Series
Бренд: ETL Страницы: 83
Promise Technology FastTrak TX4000 User Manual preview
FastTrak TX4000
Бренд: Promise Technology Страницы: 76
Sennheiser GSP 300 User Manual preview
GSP 300
Бренд: Sennheiser Страницы: 22
XMOS XK-XMP-64 Hardware Manual preview
XK-XMP-64
Бренд: XMOS Страницы: 10
Boardcon Embedded Design EM3568 User Manual preview
EM3568
Бренд: Boardcon Embedded Design Страницы: 36
HIKVISION DS-7600NI-H2/4P Series Installation Manual preview
DS-7600NI-H2/4P Series
Бренд: HIKVISION Страницы: 14
Alcatel-Lucent 1677 Brochure preview
1677
Бренд: Alcatel-Lucent Страницы: 8
Balluff BNI EIP-508 05-Z015 Series User Manual preview
BNI EIP-508 05-Z015 Series
Бренд: Balluff Страницы: 74
LAWO A_madi4 User Manual preview
A_madi4
Бренд: LAWO Страницы: 68
MSI TV@nywhere Satellite Install Manual preview
TV@nywhere Satellite
Бренд: MSI Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды