Renesas SH7616 Скачать руководство пользователя страница 498 | Manualshive

Страница: 498 / 935

background image

Section 11 Direct Memory Access Controller (DMAC)

Rev. 2.00 Mar 09, 2006 page 472 of 906
REJ09B0292-0200

Bit 0—DMA Enable Bit (DE): Enables or disables DMA transfers. In auto-request mode, the
transfer starts when this bit or the DME bit in DMAOR is set to 1. The NMIF and AE bits in
DMAOR and the TE bit must be all set to 0. In external request mode or on-chip peripheral
module request mode, the transfer begins when the DMA transfer request is received from the
relevant device or on-chip peripheral module, provided this bit and the DME bit are set to 1. As
with the auto-request mode, the TE bit and the NMIF and AE bits in DMAOR must all be set to 0.
The transfer can be stopped by clearing this bit to 0. The DE bit is initialized to 0 by a reset and in
standby mode. Its value is retained during a module standby.

Bit 0: DE

Description

0

DMA transfer disabled

(Initial value)

1

DMA transfer enabled

11.2.5

DMA Vector Number Registers 0 and 1 (VCRDMA0, VCRDMA1)

Bit:

31

30

29

…

11

10

9

8

—

—

—

…

—

—

—

—

Initial value:

0

0

0

…

0

0

0

0

R/W:

R

R

R

…

R

R

R

R

Bit:

7

6

5

4

3

2

1

0

VC7

VC6

VC5

VC4

VC3

VC2

VC1

VC0

Initial value:

—

—

—

—

—

—

—

—

R/W:

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

DMA vector number registers 0 and 1 (VCRDMA0, VCRDMA1) are 32-bit read/write registers
that set the DMAC transfer-end interrupt vector number. Only the lower eight bits of the 32 are
valid. They are written as 32-bit values, including the upper 24 bits. Values are retained in a reset,
in standby mode, and when the module standby function is used.

Bits 31 to 8—Reserved: These bits are always read as 0. The write value should always be 0.

Bits 7 to 0—Vector Number Bits 7–0 (VC7–VC0): Set the interrupt vector numbers at the end of a
DMAC transfer. Interrupt vector numbers of 0–127 can be set. When a transfer-end interrupt
occurs, the vector number is fetched and control is transferred to the specified interrupt handling
routine. The VC7–VC0 bits retain their values in a reset and in standby mode. As the maximum
vector number is 127, 0 must always be written to VC7.

«
...
496
497
498
499
500
...
»

Содержание SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7616

Бренд: National Instruments Страницы: 11

Бренд: Quatech Страницы: 27

Бренд: Amplifier Tech Страницы: 36

Linear SCP-LT8362-S-EVALZ

Бренд: Analog Devices Страницы: 8

Бренд: ZALMAN Страницы: 4

Бренд: Hama Страницы: 6

Бренд: Moxa Technologies Страницы: 51

Бренд: Omron Страницы: 13

Бренд: XJTAG Страницы: 9

Бренд: Xilinx Страницы: 8

4 Channel Input Buffer Board SDAIBB

Бренд: B&B Electronics Страницы: 22

BiPAC 5200S RC Series

Бренд: Billion Страницы: 79

Бренд: Renesas Страницы: 4

Бренд: Watchguard Страницы: 21

Бренд: HMS Страницы: 18

Бренд: DayTronic Страницы: 13

MultiModem ISIHP-2S

Бренд: Multitech Страницы: 155

Бренд: NI Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды