Raven SmarTrax MD Скачать руководство пользователя страница 77

Страница: 77 / 136

CHAPTER

P/N 016-5030-020 Rev. D

CHAPTER 5

ENVIZIO PRO AND CRUIZER II

CONSOLES CALIBRATION AND

OPERATION

INTRODUCTION

SOFTWARE COMPATIBILITY

The instructions in this manual apply to Envizio Pro consoles with software version 3.6.0.27 or higher and

Cruizer II consoles with software version 3.1.2.29627 or higher. The SmarTrax node must be running software

version 6.1.90 or higher. If the field computer or node is running with an older version of software, refer to the

Installation & Operation Manual included with the field computer for instructions software versions.

For SmarTrax MD swather operation, the SmarTrax node must be running software version 1.3.60 or higher with

the SmarTrax node software version 6.3.55 or higher. Together, these node software versions support SmarTrax MD

swather control.

SMARTRAX MD STATUS DISPLAY

FIGURE 1. Main Menu

NOTE:

The images contained in this chapter are taken from the Envizio Pro display. If a Cruizer II is being

used, the images may vary slightly from the those referenced in this chapter.

Tools

Start Button

Exit Button

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды