Raven SmarTrax MD Скачать руководство пользователя страница 39

Страница: 39 / 136

P/N 016-5030-020 Rev. D

VIPER 4

system, write down the current system settings for future reference. Recalibrate the SmarTrax MD system after

it has been reset.

NOTE:

If Reset SmarTrax is selected, the SmarTrax MD system must be recalibrated before the system can be

enabled. Refer to the Calibrate the SmarTrax MD System section on page 18 for information on

completing the SmarTrax MD system calibration.

DIAGNOSTICS TAB

•

Left and Right Manual Steer

- Used to manually test the SmarTrax MD system. Select one of the numeric

settings (1 being very low, 6 being very high) positioned around the steering wheel graphic or the Min or Max

button to steer the machine. If it does not respond as expected, the PWM values may need to be adjusted.

•

PWM Values

- Displays SmarTrax MD PWM minimum, maximum, and gain values. Adjustment of these values

is not typically necessary. Raven Industries recommends leaving these values as configured by the SmarTrax

MD system unless a technician instructs you to modify the settings.

•

Learning Mode

- Enable the learning mode feature to allow the system to automatically adjust system

response during operation. This feature allows the SmarTrax MD system to adjust the PWM minimum values

during field operation to continuously tune the steering response for monitored field conditions. Disable

learning mode to keep the system from automatically tuning the PWM minimum values and disable automatic

system response adjustment. Raven Industries does not typically recommend enabling learning mode to avoid

unexpected changes to PWM values.

NOTE:

If the PWM values are adjusted, the SmarTrax MD system will no longer automatically adjust the PWM

minimum values unless the Learning Mode function is enabled again.

Edit

SmarTrax MD

System Diagnostic

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды