Raven SmarTrax MD Скачать руководство пользователя страница 29

Страница: 29 / 136

P/N 016-5030-020 Rev. D

VIPER 4

antenna is located 3 feet behind the rear axle, the value would be entered as -3. Raven Industries

recommends mounting the antenna in front or even with the rear axle.

6. Select

Next

7. To determine the Antenna Height, measure the distance from the ground to the antenna base mounting plate.

FIGURE 16. Antenna Height Configuration Screen

8. Select the value box to enter the Antenna Height measurement using the on-screen keypad.
9. Select

Next

ENHANCED TILT CALIBRATION

NOTE:

The calibration may take a few minutes to complete.

FIGURE 17. Enhanced Tilt Calibration Wizard

1. Drive the machine forward 33 feet and park on a flat surface.

NOTE:

The machine must detect a forward motion prior to calibration to determine which direction it is

facing.

2. Follow the on-screen instructions to begin the calibration process.

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды