Raven SmarTrax MD Скачать руководство пользователя страница 47

Страница: 47 / 136

CHAPTER

P/N 016-5030-020 Rev. D

CHAPTER 4

VIPER PRO CALIBRATION AND

OPERATION

INTRODUCTION

SOFTWARE COMPATIBILITY

The instructions in this manual apply to Viper Pro software version 3.9.0.8 or higher. The SmarTrax node software

version must be running software version 6.1.90 or higher. If the Viper Pro or node is running with an older version

of software, refer to the Viper Pro Installation & Operation Manual (P/N 016-0171-122) for instructions on updating

the field computer and node software versions.

For SmarTrax MD swather operation, the SmarTrax MD unit must be running software version 1.3.60 or higher with

the SmarTrax node MD software version 6.3.55 or higher. Together, these node software versions support SmarTrax

MD swather control.

SMARTRAX MD STATUS DISPLAY

The current status of the SmarTrax MD system can be determined by the message displayed in the SmarTrax MD

section of the Viper Pro screen

Display

Message

The SmarTrax node is detected, but the operator must

accept responsibility for the operation of the SmarTrax

MD system.

SmarTrax MD is detected but not calibrated. The system

must be calibrated before it can be used.

SmarTrax MD is detected, turned on, and calibrated.

SmarTrax MD is detected and in operation in the Online

Sensitivity adjustment mode.

SmarTrax MD is detected and in operation in the Line

Acquisition Aggressiveness adjustment mode.

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды