Raven SmarTrax MD Скачать руководство пользователя страница 101

Страница: 101 / 136

P/N 016-5030-020 Rev. D

ENVIZIO PRO AND CRUIZER II CONSOLES CALIBRATION AND OPERATION

FIGURE 39. Advanced Setup #1 and Advanced Setup #2 Screens

•

Current Compensation

- Used only with certain non-steering ready machines. This feature is automatically

enabled or disabled during the calibration process and cannot be modified.

•

Anti-Oscillation

- This feature is only used with articulated machines and should not be enabled with any

other type of machine. Anti-Oscillation automatically turns on when an articulated machine is selected during

the machine configuration stage of the SmarTrax MD setup. Enabling this feature with any machine that is not

articulated may degrade the system performance.

SYSTEM DIAGNOSTICS SCREEN

The System Diagnostics screen contains the PWM values and system input diagnostic tools.

FIGURE 40. SmarTrax MD Settings and System Diagnostics Screen

•

Average Speed

- Average vehicle speed over the last hour while SmarTrax MD has been running.

•

Average

- Average distance from the desired guidance path or line during the last hour while SmarTrax MD

has been running.

•

1 Inch, 2 Inch, and 4 Inch

- The percentage of time the machine has been within the distance of the guide line

during the last hour. Press Reset to set the fields to zero.

NOTE:

The error percentages are always displayed in inches, regardless of the Display Unit selection. The

equivalent metric values are 5 cm, 10 cm, and 20 cm. On non-RTK systems, the values are 2”, 4”, and

8”.

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды