Raven SmarTrax MD Скачать руководство пользователя страница 95

Страница: 95 / 136

P/N 016-5030-020 Rev. D

ENVIZIO PRO AND CRUIZER II CONSOLES CALIBRATION AND OPERATION

2. With the engine running at the operating RPM, drive forward at a speed of 5-7 mph [8-11 km/h].

FIGURE 28. SmarTrax MD Enable Icon

3. Enable SmarTrax MD by pressing the steering wheel icon on the display or by tapping the foot/enable switch.

NOTE:

When SmarTrax MD is enabled, the steering wheel icon will turn green.

4. Allow SmarTrax MD to run while driving back and forth along the A-B guidance line.

NOTE:

If the machine is not operating to the desired specification, it may be necessary to adjust the Line

Acquire Aggressiveness and On-Line Sensitivity values. Refer to the System Adjustments section

below information on adjusting the SmarTrax MD system.

START A JOB

Refer to the Envizio Pro and Envizio Pro II Installation and Operation Manual (P/N 016-0171-148) or Cruizer II

Operation Guide (P/N 016-0171-415) for instructions on starting a job and setting guidance lines.

SYSTEM ADJUSTMENTS

LINE ACQUISITION (LA) MODE AND AGGRESSIVENESS

NOTE:

The speed of the LA mode is often limited by the speed of the machine’s hydraulic and steering

system. Increasing the LA value at the maximum vehicle speed may degrade performance of the

SmarTrax MD system.

FIGURE 29. LA Adjustment Panel

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды