Raven SmarTrax MD Скачать руководство пользователя страница 2

Страница: 2 / 136

While every effort has been made to ensure the accuracy of this document,

Raven Industries assumes no responsibility for omissions and errors. Nor is any

liability assumed for damages resulting from the use of information contained

herein.

Raven Industries shall not be responsible or liable for incidental or consequential

damages or a loss of anticipated benefits or profits, work stoppage or loss, or

impairment of data arising out of the use, or inability to use, this system or any of

its components. Raven Industries shall not be held responsible for any

modifications or repairs made outside our facilities, nor damages resulting from

inadequate maintenance of this system.

As with all wireless and satellite signals, several factors may affect the availability

and accuracy of wireless and satellite navigation and correction services (e.g.

GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the

accuracy, integrity, continuity, or availability of these services and cannot

guarantee the ability to use Raven systems, or products used as components of

systems, which rely upon the reception of these signals or availability of these

services. Raven Industries accepts no responsibility for the use of any of these

signals or services for other than the stated purpose.

Disclaimer

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды