Raven SmarTrax MD Скачать руководство пользователя страница 40

Страница: 40 / 136

HAPTER

SmarTrax™ MD Calibration & Operation Manual

Use the scroll button at the bottom of the Diagnostics prompt to toggle between the following PWM values and

steering system settings and options:

•

Disengage Sensitivity

- Proper tuning of the disengage sensitivity value allows the equipment operator to

disengage SmarTrax MD by turning the steering wheel with minimal or moderate effort. Disengage sensitivity

requires minimal adjustment.

NOTE:

If the sensitivity value is too low, the steering system may disengage in rougher fields without any

input from the operator. Raising the sensitivity value too high may make disengaging the SmarTrax

MD system at the steering wheel difficult or impossible.

•

Target Current and Actual Current

- Current readings performed on SmarTrax systems MD. Target Current is

what the system expects to read. Actual Current displays the amount of current the system is using to steer the

machine. These values are used to adjust system performance.

•

Current Compensation

- This feature is not used in SmarTrax MD systems.

•

Anti-Oscillation-Articulated Machines

- This feature is not used in SmarTrax MD systems.

SENSOR STATUS

Edit

SmarTrax MD

Sensor Status

Zero Yaw

Button

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды