Raven SmarTrax MD Скачать руководство пользователя страница 37

Страница: 37 / 136

P/N 016-5030-020 Rev. D

VIPER 4

ON-LINE (OL) MODE AND SENSITIVITY

FIGURE 30. OL Mode Indicator

NOTE:

The screen in the figure above illustrates an example of a situation in which SmarTrax MD is operating

in OL mode. This mode will remain active as long as the machine steers within 24 inches [60 cm] of

the displayed guidance line.

The OL Sensitivity value affects the response of the machine while steering within 24 inches [60 cm] of the

displayed guidance line. If the machine tends to slowly weave across the guidance line and does not remain within

24 inches [60 cm] of the desired path, increase the OL Sensitivity value one increment at a time, allowing

SmarTrax MD at least 30 seconds between adjustment to adjust to the change in the value.

Setting the OL Sensitivity value too high may cause the machine to over-correct or become jittery while on the

line. Lowering the value in these situations will allow the vehicle to remain on the desired path.

ADVANCED SETUP TOOLS AND SYSTEM DIAGNOSTICS

Advanced setup tools allow fine-tuning of the system to adjust for operating conditions and improve steering

accuracy.

NOTE:

Some features or settings are not able to be adjusted unless SmarTrax MD is in an active job.

NOTE:

Some features or settings are configured during the SmarTrax MD calibration wizard and cannot be

modified or changed without resetting the SmarTrax MD system. Refer to Reset Calibration section on

page 37 for additional assistance with resetting the SmarTrax MD system to default settings.

SYSTEM INFORMATION TAB

NOTE:

To change the Sensor Type, Machine Type, Control Device, or Wheel Base settings, the SmarTrax MD

system must be reset and recalibrated.

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды