Raven SmarTrax MD Скачать руководство пользователя страница 100

Страница: 100 / 136

HAPTER

SmarTrax™ MD Calibration & Operation Manual

•

Calibrate 3D

- Used to calibrate the enhanced tilt compensation feature. Refer to the Enhanced Tilt Calibration

section on page 82 for the calibration procedure.

NOTE:

Select Accept to save changes to the 3D Terrain Compensation screen and return to the SmarTrax MD

Information screen. Select Exit to exit the 3D Terrain Compensation setup screen without saving any

changes and return to the SmarTrax MD Information screen.

ADVANCED SETUP SCREEN

The Advanced Setup screen contains advanced diagnostic information used to fine-tune the SmarTrax MD system

and improve steering accuracy.

FIGURE 38. SmarTrax MD Settings and Advanced Setup Screen #1

•

HDOP Limit

- Horizontal Dilution of Precision (HDOP) is an indicator of the quality of the GPS signal. A high

HDOP indicates that not enough satellites are distributed evenly throughout the sky, diminishing the accuracy

of the guidance system. The number displayed is the maximum number SmarTrax MD will allow to run. Raising

this number may degrade system performance.

•

GPS Baud

- The rate the system uses to communicate with the GPS receiver. This value must match the value of

the GPS receiver installed in the system.

•

Disengage Setting

- Controls the amount of steering input required to disengage the SmarTrax MD system.

Higher values require more input.

•

Service Mode

- Used only for software programming purposes and is not accessible without a code.

•

Exit

- Returns to the SmarTrax MD Controller screen.

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды