Raven SmarTrax MD Скачать руководство пользователя страница 35

Страница: 35 / 136

P/N 016-5030-020 Rev. D

VIPER 4

FIGURE 27. Steering Calibration Screen

1. Position the machine in an open space with several acres of smooth ground available to perform the machine’s

steering calibration.

2. Press the foot/engage switch to begin calibration.

NOTE:

During calibration, the machine will turn hard to the left or right and progressively turn in the

opposite direction, then turn hard in that direction and progressively turn back in the opposite

direction. Adjust the speed and vehicle location as necessary.

NOTE:

If an error message is displayed during calibration, refer to the “Error Messages” section on page 100

for possible causes and corrective action to complete the calibration process.

START A JOB

Refer to the ROS (Raven Operating System) Basic Operation Manual (P/N 016-0171-539) for instructions on

starting a job and setting guidance lines.

SYSTEM ADJUSTMENTS

System tools allow fine-tuning of the system to adjust for operating conditions and improve steering accuracy. To

adjust the steering response in the field computer, press and hold the SmarTrax MD widget while within a job. The

following screen will appear:

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды