Raven SmarTrax MD Скачать руководство пользователя страница 11

Страница: 11 / 136

CHAPTER

P/N 016-5030-020 Rev. D

CHAPTER 2

INTRODUCTION

Congratulations on your purchase of the Raven SmarTrax MD system! This system is designed to provide cutting-

edge, hands-free steering of the machine via Global Positioning System (GPS) coordinates.

The instructions in this manual are designed to assist in the proper calibration and operation of the SmarTrax MD

system when used with the Viper 4, Viper Pro, Envizio Pro or Envizio Pro II, and Cruizer II field computers.

IMPORTANT:

Installation of the SmarTrax MD system must be completed before calibrating the system. If you have

questions regarding the installation of the SmarTrax MD system, refer to the SmarTrax MD Installation

Manual provided with the installation kit.

IMPORTANT:

The Raven field computer/controller must be calibrated specifically for the vehicle before being used to

operate the SmarTrax MD system. For questions about the field computer, refer to the Installation &

Operation Manual provided with the field computer.

NOTE:

Machine-specific installation kits are not available for all machine makes and models.

SMARTRAX MD PART IDENTIFICATION

Latch

Road Switch

Status Indicator

Node Harness

Connection Port

Anti-Rotation Pin

Installation

Locations

Front

Back

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды