Raven SmarTrax MD Скачать руководство пользователя страница 68

Страница: 68 / 136

HAPTER

SmarTrax™ MD Calibration & Operation Manual

The OL Sensitivity value affects the response of the machine while steering within 24 inches [60 cm] of the

displayed guidance line. If the machine tends to slowly weave across the guidance line and does not remain within

24 inches [60 cm] of the desired path, increase the OL Sensitivity value one increment at a time, allowing SmarTrax

MD at least 30 seconds between adjustment to adjust to the change in the value.

Setting the OL Sensitivity value too high may cause the machine to over-correct or become jittery while on the

line. Lowering the value in these situations will allow the vehicle to remain on the desired path.

STX SETUP SCREEN

FIGURE 34. SmarTrax MD Setup Screen

NOTE:

To change the Machine Type, Control Device, or Wheel Base settings, the SmarTrax MD system must

be reset and recalibrated.

•

Set Antenna Measurements

- Allows the Antenna Height and Antenna Position measurements to be changed.

•

Recal Hyd

- Restarts the machine’s steering calibration process. Refer to Calibrate the Machine’s Steering

System section on page 57 for information on completing the machine’s steering calibration.

•

Reset STX

- Resets the SmarTrax MD system to the default values.

IMPORTANT:

If Reset STX is selected, the SmarTrax MD system must be recalibrated before the system can be enabled.

Refer to Calibrate the SmarTrax MD System section on page 47 for information on completing the

SmarTrax MD system calibration.

•

Set

- Displays the Sensor Status screen.

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды