Raven SmarTrax MD Скачать руководство пользователя страница 67

Страница: 67 / 136

P/N 016-5030-020 Rev. D

VIPER PRO CALIBRATION AND OPERATION

FIGURE 31. SmarTrax MD Information Screen

LINE ACQUISITION (LA) MODE AND AGGRESSIVENESS

NOTE:

The speed of the LA mode is often limited by the speed of the machine’s steering system. Increasing

the LA value at the maximum vehicle speed may degrade performance of the SmarTrax MD system.

FIGURE 32. LA Mode Indicator

The LA Aggressiveness value affects how quickly the machine steers toward a displayed guidance line when it is

traveling further than 24 inches [60 cm] from the desired path. If the machine drives past the line and has to drive

back to it, increase the LA Aggressiveness value one increment at a time, allowing SmarTrax MD at least 30

seconds between adjustments to adjust to the change in the value.

Setting the LA Aggressiveness value too high may cause the machine to steer into the guidance line too quickly

and weave around the guidance line. Lowering the value in these situations will allow the machine to settle on the

line.

ON-LINE (OL) MODE AND SENSITIVITY

FIGURE 33. OL Mode Indicator

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды