Raven SmarTrax MD Скачать руководство пользователя страница 98

Страница: 98 / 136

HAPTER

SmarTrax™ MD Calibration & Operation Manual

SMARTRAX MD INFORMATION SCREEN

FIGURE 34. SmarTrax MD Settings and SmarTrax MD Information Screens

NOTE:

To change the Sensor Type, Machine Type, Control Device, or Wheel Base settings, the SmarTrax MD

system must be reset and recalibrated.

•

Antenna Height

- Selecting the Set icon next to the Antenna Height setting allows the Antenna Height

measurement to be changed.

•

Antenna Fore/Aft

- Selecting the Set icon next to the Antenna Fore/Aft setting allows the Antenna Fore/Aft

position measurement to be changed.

•

Sensor Type

- Selecting the sensor set icon next to the sensor type setting displays the Sensor Status screen.

FIGURE 35. SmarTrax MD Information and Sensor Setup Screen #1

• The Yaw Sensor Setup screen displays the yaw sensor status information:

◦

Current Wheel Angle

- An approximation of the machine’s wheel angle.

◦

Current Reading

- The current value of the encoder.

◦

Zero Yaw Button

- Recalibrates the yaw sensor to zero. The machine must be at a full stop before

recalibrating the yaw sensor.

◦

Encoder Cal

- The ratio of the steering wheel movement to the machine’s wheel movement.

Sensor

Set Icon

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды