Raven SmarTrax MD Скачать руководство пользователя страница 73

Страница: 73 / 136

P/N 016-5030-020 Rev. D

VIPER PRO CALIBRATION AND OPERATION

of the guidance system. The number displayed is the maximum number SmarTrax MD will allow to run. Raising

this number may degrade system performance.

•

GPS Baud

- The rate the system uses to communicate with the GPS receiver. This value must match the value

of the GPS receiver installed in the system.

•

Anti-Oscillation

- This feature is only used with articulated machines and should not be enabled with any

other type of machine. Anti-Oscillation automatically turns on when an articulated machine is selected during

the machine configuration stage of the SmarTrax MD setup. Enabling this feature with any machine that is not

articulated may degrade the system performance.

•

Service Page

- Used only for software programming purposes and is not accessible without a code.

•

Exit

- Returns to the SmarTrax MD Controller screen.

ENHANCED TILT SETUP SCREEN

The SmarTrax MD 3D terrain compensation feature adjusts incoming GPS messages, compensating for roll (side-

to-side tilting), pitch (front-to-rear tilting), and yaw (twisting or turning) of the machine.

FIGURE 41. Terrain Compensation Information Screen

•

Roll, Pitch, Yaw, and Yaw Rate

- Real-time measurement data used by the 3D terrain compensation feature.

•

Direction of Travel

- Indicates the direction in which the machine is traveling. If the direction is incorrect, drive

forward and press the Send Forward Command button. Verify the direction of travel is displayed correctly

when the machine is being driven in both forward and reverse.

•

Forward and Downward

- Indicate the orientation of the node programmed during calibration of the

SmarTrax MD system.

•

Calibrate 3D

- Used to calibrate the 3D terrain compensation feature. Refer to the Enhanced Tilt Calibration

section on page 52 for the calibration procedure.

•

ACTIVE/BYPASSED

- Used to toggle the 3D terrain compensation feature on and off.

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды