manualshive.com logo in svg

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Raven SmarTrax MD - уникальное устройство для автоматического управления навигацией в сельском хозяйстве. Установочное руководство и другие руководства доступны для загрузки бесплатно на нашем сайте. Улучшите эффективность своей работы с помощью этого революционного устройства. Скачайте руководство с manualshive.com.

Поделиться
Скачать
background image

Table of Contents

P/N 016-5030-020 Rev. D

i

Chapter 1 

Important Safety Information.............................................................................  

1

General ............................................................................................................................................................................

1

Instructions for Wire Routing .................................................................................................................................

2

Chapter 2 

Introduction.............................................................................................................  

5

SmarTrax MD Part Identification ...........................................................................................................................

5

Installation ......................................................................................................................................................................

6

Recommendations .................................................................................................................................................................

6

Point of Reference .......................................................................................................................................................

6

Updates ...........................................................................................................................................................................

6

     Updating the Node .........................................................................................................................................................

6

Updating the Mechanical Drive ........................................................................................................................................

6

Chapter 3 

Viper 4.......................................................................................................................  

9

Widget and Button Definitions ..............................................................................................................................

9

Initial Startup ..............................................................................................................................................................

10

Data Transfer ..........................................................................................................................................................................

10

GPS Configuration ...............................................................................................................................................................

10

Internal GPS Receiver ..................................................................................................................................

10

External 600S GPS Receiver  ......................................................................................................................

12

External GPS Receiver  .................................................................................................................................

14

SmarTrax MD Terms of Use ..............................................................................................................................................

16

Machine Configuration ......................................................................................................................................................

16

Set Up Machine Profile(s) - Optional ....................................................................................................

16

Machine-Specific Configuration  .............................................................................................................

17

Calibrate the SmarTrax MD System ..................................................................................................................

18

Node Orientation .................................................................................................................................................................

19

Configuring Wheel Base and Antenna Offsets .........................................................................................................

19

Enhanced Tilt Calibration ..................................................................................................................................................

23

System Disengage Calibration ........................................................................................................................................

26

Engage Switch .......................................................................................................................................................................

27

Wheel Angle Sensor (WAS) Calibration .......................................................................................................................

27

Calibrate the Machine’s Steering System .......................................................................................................

28

Start a Job ...................................................................................................................................................................

29

System Adjustments ................................................................................................................................................

29

Line Acquisition (LA) Mode and Aggressiveness .....................................................................................................

30

On-Line (OL) Mode and Sensitivity ...............................................................................................................................

31

Advanced Setup Tools and System Diagnostics ..........................................................................................

31

System Information Tab ....................................................................................................................................................

31

Diagnostics Tab .....................................................................................................................................................................

33

Sensor Status .........................................................................................................................................................................

34

SmarTrax 3D Compensation Tab ....................................................................................................................................

35

GPS Setup Tab .......................................................................................................................................................................

36

Error Log Tab .........................................................................................................................................................................

37

Reset Calibration ..................................................................................................................................................................

37

Routine Operation ...................................................................................................................................................

38

Engage SmarTrax ..................................................................................................................................................................

38

Содержание SmarTrax MD









































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmarTrax MD

Jensen Marine MSR3012 Installation And Operation Manual preview
MSR3012
Бренд: Jensen Marine Страницы: 18
SereneLife SLBSP10 Quick Manual preview
SLBSP10
Бренд: SereneLife Страницы: 2
Hamworthy Weymouth Series Installation, Commissioning And Servicing Instructions preview
Weymouth Series
Бренд: Hamworthy Страницы: 28
Burmester 151 Musiccenter Short Operating Instructions preview
151 Musiccenter
Бренд: Burmester Страницы: 20
M&S Systems MC602 Owner'S Manual preview
MC602
Бренд: M&S Systems Страницы: 12
Waterite Vectamaxx RSL Owner'S Manual preview
Vectamaxx RSL
Бренд: Waterite Страницы: 24
Riello 7200/1 170 Plus Installer And User Manual preview
7200/1 170 Plus
Бренд: Riello Страницы: 16
Philips FW 780P Instructions For Use Manual preview
FW 780P
Бренд: Philips Страницы: 28
Silvercrest SSB 50 A1 Operating Instructions Manual preview
SSB 50 A1
Бренд: Silvercrest Страницы: 23
Silvercrest SSB 36 A1 Operating Instructions Manual preview
SSB 36 A1
Бренд: Silvercrest Страницы: 46
Sony HCD-RXD6AV Service Manual preview
HCD-RXD6AV
Бренд: Sony Страницы: 13
Sony hcd-tb20 Operating Instructions Manual preview
hcd-tb20
Бренд: Sony Страницы: 36
Sony HCD-TB10 Service Manual preview
HCD-TB10
Бренд: Sony Страницы: 56
Sony hcd-vx888 Service Manual preview
hcd-vx888
Бренд: Sony Страницы: 84
Sony HCD-VX550 Service Manual preview
HCD-VX550
Бренд: Sony Страницы: 82
Sony HCD-VX88 Service Manual preview
HCD-VX88
Бренд: Sony Страницы: 84
Sony HCD-VX77 Service Manual preview
HCD-VX77
Бренд: Sony Страницы: 84
Sony HCD-VX3A Service Manual preview
HCD-VX3A
Бренд: Sony Страницы: 82

Бренды по названию

Популярные бренды

Загрузить еще бренды