Raven SmarTrax MD Скачать руководство пользователя страница 33

Страница: 33 / 136

P/N 016-5030-020 Rev. D

VIPER 4

ENGAGE SWITCH

1. Review the on-screen instructions.
2. Press and release the foot switch or engage switch.

NOTE:

The SmarTrax Setup MD Wizard will automatically advance to the next step in the calibration process

when the engage switch is detected.

WHEEL ANGLE SENSOR (WAS) CALIBRATION

The WAS calibration is required on the SmarTrax MD system. Once the WAS is detected in the system, the

following screen will be displayed:

FIGURE 26. WAS Calibration Screen

1. While driving slowly, turn the steering wheel fully to the left wheel lock.
2. Select

Left

3. Turn the steering wheel fully to the right wheel lock.
4. Select

Right

5. Select

Next

NOTE:

If the steering wheel continues to turn when the wheels are turned fully to the left or right, be sure to

stop turning the steering wheel when the machine’s wheels stop moving.

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды