manualshive.com logo in svg

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Raven SmarTrax MD - уникальное устройство для автоматического управления навигацией в сельском хозяйстве. Установочное руководство и другие руководства доступны для загрузки бесплатно на нашем сайте. Улучшите эффективность своей работы с помощью этого революционного устройства. Скачайте руководство с manualshive.com.

Поделиться
Скачать
background image

Table of Contents

P/N 016-5030-020 Rev. D

iii

Node Orientation .................................................................................................................................................................

77

Configuring Wheel Base and Antenna Offsets .........................................................................................................

77

Enhanced Tilt Calibration ..................................................................................................................................................

82

Steering Switch Calibration ..............................................................................................................................................

84

Engage Switch Calibration ................................................................................................................................................

85

Wheel Angle Sensor (SPS) Calibration .........................................................................................................................

86

Calibrate the Machine’s Steering System .......................................................................................................

86

Complete the SmarTrax MD Calibration Process .........................................................................................

88

Start a Job ...................................................................................................................................................................

89

System Adjustments ................................................................................................................................................

89

Line Acquisition (LA) Mode and Aggressiveness .....................................................................................................

89

On-Line (OL) Mode and Sensitivity ...............................................................................................................................

90

Advanced Setup and Diagnostics ......................................................................................................................

91

SmarTrax MD Information Screen .................................................................................................................................

92

Enhanced Tilt Calibration Setup Screen ......................................................................................................................

93

Advanced Setup Screen .....................................................................................................................................................

94

System Diagnostics Screen ...............................................................................................................................................

95

Reset Default ..........................................................................................................................................................................

97

Recalibrating Hydraulics ....................................................................................................................................................

97

Routine Operation ...................................................................................................................................................

98

Engaging SmarTrax MD .....................................................................................................................................................

98

System Settings   ..................................................................................................................................................................

98

Chapter 6 

Troubleshooting ................................................................................................... 

99

Node ..............................................................................................................................................................................

99

Mechanical Drive Diagnostics ...........................................................................................................................

100

Error Messages  .......................................................................................................................................................

100

SmarTrax MD Operation  ....................................................................................................................................

103

Chapter 7 

System Diagrams...............................................................................................  

107

Chapter 8 

Roadway Homologation Certification .......................................................... 

111

Содержание SmarTrax MD









































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmarTrax MD

Magnavox MAS-80 Manual Del Usuario preview
MAS-80
Бренд: Magnavox Страницы: 23
Watts AERCO 58025-05 Technical Instructions preview
AERCO 58025-05
Бренд: Watts Страницы: 24
HK Audio Cohedra Manual preview
Cohedra
Бренд: HK Audio Страницы: 105
Exibel BDX610 Manual preview
BDX610
Бренд: Exibel Страницы: 64
Curtis RCD633 Specification Sheet preview
RCD633
Бренд: Curtis Страницы: 1
Beko BEKOMAT 16i CO Translation Of Original Installation And Operation Manual preview
BEKOMAT 16i CO
Бренд: Beko Страницы: 76
Sound Freaq SFQ-03I User Manual preview
SFQ-03I
Бренд: Sound Freaq Страницы: 19
Philips FW-C90 Specifications preview
FW-C90
Бренд: Philips Страницы: 2
Philips FW-C870 Specifications preview
FW-C870
Бренд: Philips Страницы: 2
Philips FW-C85/18 Specifications preview
FW-C85/18
Бренд: Philips Страницы: 2
Philips FW-C80 Specifications preview
FW-C80
Бренд: Philips Страницы: 2
Philips FW-C90 User Manual preview
FW-C90
Бренд: Philips Страницы: 29
Philips FW-C870 User Manual preview
FW-C870
Бренд: Philips Страницы: 30
Philips FW-D596 User Manual preview
FW-D596
Бренд: Philips Страницы: 48
Philips FW-D5/21 Service Manual preview
FW-D5/21
Бренд: Philips Страницы: 100
Philips FW-C870/19 Service Manual preview
FW-C870/19
Бренд: Philips Страницы: 105
Philips FW-D550 Manual preview
FW-D550
Бренд: Philips Страницы: 48
Philips FW-C870 Service Manual preview
FW-C870
Бренд: Philips Страницы: 108

Бренды по названию

Популярные бренды

Загрузить еще бренды