Raven SmarTrax MD Скачать руководство пользователя страница 93

Страница: 93 / 136

P/N 016-5030-020 Rev. D

ENVIZIO PRO AND CRUIZER II CONSOLES CALIBRATION AND OPERATION

NOTE:

To ensure the calibration is successful, the number of starts and stops during the calibration process

should be limited. If it is necessary to pause the calibration process, turn the steering wheel or tap the

foot/enable switch. Tap the foot/enable switch again to resume calibration.

FIGURE 26. Steering Calibration Screens

1. Position the machine in an open space with several acres of smooth ground available to perform the machine’s

steering calibration.

2. Press the foot/engage switch to begin calibration.

NOTE:

During calibration, the machine will turn hard to the left and then to the right. Adjust the speed and

vehicle location as necessary.

NOTE:

After calibration is complete, the SmarTrax MD menu will be displayed.

NOTICE

The calibration of the machine’s steering system

should be performed in a field or other large,

open space and during conditions similar to

normal vehicle operation.

If the ground or surface is slippery, muddy, or

freshly tilled, the SmarTrax MD system may learn

incorrect steering responses for normal

operating conditions.

Ensure the machine’s hydraulics are operating

properly and there are no other mechanical

issues that may affect the performance of the

SmarTrax MD system.

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды