Raven SmarTrax MD Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 136

background image

C

HAPTER

8

112

SmarTrax™ MD Calibration & Operation Manual

Technical Report No. /

Technischer Bericht Nr.:

Manufacturer /

Hersteller:

Type /

Typ:

13-00314-CC-GBM-00
Raven Industries
SmarTrax MD

AM-HZSF

Page /

Seite

: 2 / 14

1. General

/

Allgemeines:

1.1.

The Technical Report includes the test of the system SmarTrax MD of the
manufacturer Raven Industries.
SmarTrax MD is a mechanical drive unit and together with the controller
SmarTrax MD Node and the monitor SmarTrax Cruiser II Control (opt.
monitor Envizio Pro or monitor Viper Pro) it is used for the GPS based
steering of vehicles.

The system SmarTrax MD is designed for the use in agricultural or forestry
tractors as well as in agricultural or forestry self-propelled working
machines.

It is not allowed for on road use.

The testing includes the check of the conformity with the directive
2009/66/EC as well as the § 38 StVZO.

In addition the electromagnetic compatibility of components of the system
has been proved. /

Der Technische Bericht beinhaltet die Prüfung des Systems SmarTrax MD des
Herstellers Raven Industries.
SmarTrax MD ist eine mechanische Antriebseinheit zur GPS-basierten
Lenkung von Fahrzeugen in Verbindung mit dem Rechner SmarTrax MD Node
und dem Montior SmarTrax Cruiser II Control (ww. Monitor Envizio Pro oder Mo-
nitor Viper Pro).

Das System SmarTrax MD ist zur Verwendung in land- oder forstwirtschaftlichen
Zugmaschinen und land- oder forstwirtschaftlichen selbstfahrenden
Arbeitsmaschinen vorgesehen.

Es darf nur außerhalb des öffentlichen Straßenverkehrs eigesetzt werden.

Die Prüfungen umfassen die Überprüfung der Konformität mit der Richtlinie
2009/66/EC sowie mit § 38 StVZO.

Zusätzlich wurden Komponenten des Systems auf die elektromagnetische
Verträglichkeit überprüft.

«
...
116
117
118
119
120
...
»

Содержание SmarTrax MD









































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmarTrax MD

Бренд: YOKOGAWA Страницы: 132

FUSION Apollo MS-WB670

Бренд: Garmin Страницы: 44

Бренд: uAvionix Страницы: 4

Бренд: Panasonic Страницы: 45

Бренд: TMQ Страницы: 24

Бренд: JVC Страницы: 101

Бренд: Philips Страницы: 94

Бренд: Sony Страницы: 14

Бренд: Sony Страницы: 19

HCD-ZX9 - Receiver Cd

Бренд: Sony Страницы: 40

Бренд: Sony Страницы: 45

Бренд: Sony Страницы: 38

Бренд: Sony Страницы: 43

Бренд: Sony Страницы: 78

Бренд: Sony Страницы: 74

Бренд: Sony Страницы: 86

Бренд: Sony Страницы: 84

HCD-XG500 - Bookshelf System

Бренд: Sony Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды