Raven SmarTrax MD Скачать руководство пользователя страница 25

Страница: 25 / 136

P/N 016-5030-020 Rev. D

VIPER 4

NODE ORIENTATION

FIGURE 11. Node Orientation Screen

3. Ensure that the machine is parked on a level surface.
4. Select the number that corresponds with the node arrow number pointing toward the front of the machine.

IMPORTANT:

Selecting the incorrect node arrow number may cause poor steering performance!

NOTE:

The SmarTrax MD calibration wizard will perform an initial calibration on the SmarTrax MD tilt sensors.

The wizard will automatically advance to the next step in the calibration process once the node

calibration is complete.

CONFIGURING WHEEL BASE AND ANTENNA OFFSETS

If a generic machine profile was selected during the machine configuration process, the Wheel Base, Antenna

Position, and Antenna Height values must be entered into the SmarTrax system.

IMPORTANT:

If a specific machine profile was selected during the machine configuration process, the Wheel base,

Antenna Position, and Antenna Height measurements will be automatically populated in the screen.

However, the antenna mounting position may vary on the machine, so it is important to re-measure the

Antenna Position and Antenna Height to verify that the setting in the Viper 4 is correct. The Wheel Base

value cannot be changed.

NOTICE

The Wheel Base, Antenna Position, and Antenna

Height values are critical to the operation of the

SmarTrax system. Measure these dimensions

accurately to ensure optimal SmarTrax MD

system performance!

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды