background image

 

SYSTIMAX

®

 Solutions                    

www.commscope.com

 

Instruction Sheet 860479229 

Issue 7, May 2013

 

 
 

SYSTIMAX 360

 Ultra High-Density Shelf Instructions 

 

 

 

 

© 2013 CommScope, Inc.  All rights reserved 

 

Page 1 of 15 

 

General 

The 

SYSTIMAX

 

360

 ultra high-density (UHD) shelf, 3603D-1U-UP, is a 19-inch (483mm) wide fiber optic shelf 

that provides three positions for 

InstaPATCH

®

 

360

  UHD modules or UHD panels.  A unique pivoting feature 

allows access to the high-density connector patching field. The shelf provides a secure, enclosed slack trunk 
cable storage and features a removable cover.  It is intended for indoor use, but may be used outdoors in a 
suitable protective enclosure.  The shelf is available as an empty shelf where modules or panels are not included 
and must be ordered separately or in preloaded versions that include modules (in ALPHA or BETA orientation) or 
panels. Additional shelf configurations provide for fusion splicing when using LC pass-thru panels. 

Ordering information is listed below:   
 

Material ID 

Part No. 

Description 

760110999 

3603D-1U-UP 

Fiber shelf, 1U, UHD, empty 

760136457 

3603D-1U-144LC-LS-A 

3603D-1U-UP UHD shelf with three  3603M-48LC-LS UHD modules in 
ALPHA orientation 

760136465 

3603D-1U-144LC-LS-B 

3603D-1U-UP UHD shelf with three  3603M-48LC-LS UHD modules in  
BETA orientation 

760136432 

3603D-1U-144LC-SM-A 

3603D-1U-UP UHD shelf with three  3603M-48LC-SM UHD modules in 
ALPHA orientation 

760136440 

3603D-1U-144LC-SM-B 

3603D-1U-UP UHD shelf with three  3603M-48LC-SM UHD modules in 
BETA orientation 

760136473 

3603D-1U-72MPO 

3603D-1U-UP UHD shelf with three 3603P-24MPO UHD panels 

760149054 

3603D-1U-144LC-TS-DP 

Splice shelf with three 

TeraSPEED

®

 (SM) LC pass-thru panels 

760149062 

3603D-1U-144LC-LS-DP 

Splice shelf with three 

LazrSPEED

®

 LC pass-thru panels 

 

 

SYSTIMAX 360

 3D-UHD Shelf in Closed Position and Open Position for Patch Cord Access 

Содержание 3603D-1U-144LC-LS-A
















Отзывы: