Raven SmarTrax MD Скачать руководство пользователя страница 42

Страница: 42 / 136

HAPTER

SmarTrax™ MD Calibration & Operation Manual

GPS SETUP TAB

•

SmarTrax HDOP Limit

- Horizontal Dilution of Precision (HDOP) is an indicator of the quality of the GPS signal.

A high HDOP indicates that not enough satellites are distributed evenly throughout the sky, diminishing the

accuracy of the guidance system. The number displayed is the maximum number SmarTrax MD will allow to

run. Raising this number may degrade system performance.

NOTE:

The default SmarTrax HDOP limit is 2.5. Increasing the HDOP limit may degrade SmarTrax

performance. Decreasing the HDOP limit may cause SmarTrax MD to disengage more often.

•

SmarTrax GPS Baud

- The rate the system uses to communicate with the GPS receiver. This value is typically set

to 19200, but it can be changed to match the baud rate of receivers that cannot be easily changed to 19200.

NOTE:

With the 600S GPS Receiver and SmarTrax MD software version 7.6 and newer, the GPS baud will

automatically change to 115200 to allow communication with the 600S for configuration or changing

settings.

•

SmarTrax GPS Frequency

- The GGA message update frequency in hertz (Hz).

•

Minimum GPS Correction

- This setting is used to select the correction source providing the minimum

accuracy allowable for SmarTrax operation. This selection may be used to prevent the SmarTrax system from

sudden course changes if the desired correction source is lost. For example, selecting RTK for this feature will

disengage SmarTrax if RTK corrections are lost.

Edit

SmarTrax MD

GPS

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды