Raven SmarTrax MD Скачать руководство пользователя страница 94

Страница: 94 / 136

HAPTER

SmarTrax™ MD Calibration & Operation Manual

FIGURE 27. Steering Calibration Resume Screen

If the wheels strike the stops at the end of travel or if a high degree of effort is required to turn the wheels during

calibration, steering may be disengaged. If steering becomes disengaged during calibration:
• Press

Stop

to cancel the calibration. Adjust the amount of effort required to disengage the steering system by

pressing the up or down arrow button.

• Press

Back

to return to the calibration process. Retry is most commonly used when the system is intentionally

disengaged to avoid obstacles.

COMPLETE THE SMARTRAX MD CALIBRATION PROCESS

NOTE:

The Line Acquire Aggressiveness and On-Line Sensitivity values may be adjusted to further tune the

system or to adjust for operating conditions. Refer to the System Adjustments section below for

further information on system adjustments.

1. Start a job and set a straight A-B guidance line.

NOTE:

Refer to the Envizio Pro Installation and Operation Manual (P/N 016-0171-148) or the Cruizer II

Operation Guide (P/N 016-0171-415) for information on starting a job.

NOTICE

The calibration of the machine’s steering system

should be performed in a field or other large,

open space and during conditions similar to

normal vehicle operation.

If the ground or surface is slippery, muddy, or

freshly tilled, the SmarTrax MD system may learn

incorrect steering responses for normal

operating conditions.

Ensure the machine’s hydraulics are operating

properly and there are no other mechanical

issues that may affect the performance of the

SmarTrax MD system.

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды