Raven SmarTrax MD Скачать руководство пользователя страница 107

Страница: 107 / 136

P/N 016-5030-020 Rev. D

101

TROUBLESHOOTING

HC Volt L

SmarTrax MD has detected a supply

voltage less than 10.6 volts.

Check the battery voltage and

connections.

High HDOP

Insufficient GPS signal is being received.

Wait a few minutes to see if signal

improves.

HS Fail

The hardware inside the mechanical

drive is damaged.

1. Navigate to the SmarTrax Manual Steering

screen.

2. Toggle the master switch on and off,

verifying that the Raven LED logo

changes from white steady to blue

steady.

3. Drive the motor at various settings while

monitoring the Actual Current value. If no

current is drawn and the problem persists,

replace the mechanical drive.

HW Wrong

The device does not support the

installed software.

1. Verify the software versions of the

mechanical drive and node are

compatible.

2. Reprogram the devices with the correct

software version.

Low Sats

The GPS receiver is not receiving signal

from enough satellites.

Move to an open area and wait a few

minutes to see if more satellites are

found.

MsSw Fail

The hardware inside the mechanical

drive is damaged.

Manually toggle the master switch on

the mechanical drive between “ON” and

“OFF”.
Replace the SmarTrax mechanical drive.

MsSw Off

The master switch is in the “OFF”

position.

Manually toggle the master switch on

the mechanical drive to the “ON”

position.

No A-B Msg

The A-B line has not been set on the

field computer.

Set the A-B line in the field computer.

No communication from the field

computer.

Verify cabling is correct and secure.
• Viper Pro - Ensure that “Send Guidance

Messages” is selected.

• Envizio Pro - Ensure that GPS Source

“Internal via Tilt or SmarTrax” is

selected.

• Viper 4 - Ensure “SmarTrax GPS on

DGPS” is selected.

No Cal

SmarTrax MD has not been calibrated.

Calibrate the SmarTrax MD system using

the calibration wizard.

No Diff

The GPS receiver has not acquired

differential.

Wait a few minutes to see if the GPS

differential is acquired.
Check the receiver differential settings.

No GGA

No GGA messages are being received.

Check the receiver settings. The

recommended setting is 10Hz.

No GPS

No GPS information is being received.

Verify the GPS receiver is properly

installed and configured.

Message

Possible Cause

Corrective Action

Содержание SmarTrax MD








































































































































Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды

Raven SmarTrax MD, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание SmarTrax MD

Отзывы:

Похожие инструкции для SmarTrax MD

Бренды по названию

Популярные бренды