PREVOST X3-45 COMMUTER Скачать руководство пользователя | Manualshive

Страница: 330 / 549

background image

SECTION 14: STEERING

8

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Section 14 revised April 2018)

FIGURE 11: LOCKING THE CLOCKSPRING IN PLACE

NOTE

The clockspring mechanism permits a certain
number of turns in each direction. At the
moment of reinstalling the steering wheel, if
the clockspring is not at its neutral position,
the number of available turns will be reduced.
That may damage the clockspring if the
steering wheel is turned to its maximum
amplitude.

7.2 INSTALLATION

1. Route the white horn wire and the 4-pin

connector through the opening on the
steering wheel.

2. Align the mark on the steering wheel hub

with the mark on the spline shaft and slide
the wheel onto the shaft.

3. Tighten wheel retaining nut to a torque of

35-45 lbf·ft.

4. Plug the 4-pin connector and connect the

white horn wire to the center pad.

5. Reinstall the center pad and test for proper

horn functioning.

7.3 CLOCKSPRING

REPLACEMENT

1. Remove the steering wheel.

2. Remove the 2 clockspring mounting screws

and then remove the clockspring. You will
have to disconnect the clockspring harness
connector located lower along the steering
wheel column. If necessary, remove the
steering column covers (Figure 8).

3. Route the new clockspring harness through

the opening in the clockspring support

(Figure 12). Plug the connector at the base
of the steering wheel column and fix harness
along the steering wheel column.

FIGURE 12: CLOCKSPRING INSTALLATION

4. Mount the clockspring in place with 2

screws.

5. Break the paper seal and rotate the center

part of the clockspring about 50° clockwise
(Figure 13). This step is necessary for the
installation of the steering wheel.

FIGURE 13: PROPER CLOCKSPRING POSITION

6. Reinstall the steering wheel.

8. TURNING ANGLE ADJUSTMENT

The maximum turning angle is set through two (2)
steering stop screws installed on the axle center.
Steering stop screws are factory adjusted to
accommodate the chassis design, and therefore,
do not require adjustment on new vehicles.
However, these should be checked and adjusted
if necessary, any time a steering system
component is repaired, disassembled or adjusted.
Refer to section 10

"Front Axle"

under heading

‘’6.4 ‘’Turning Angle Adjustment".

«
...
328
329
330
331
332
...
»

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X3-45 COMMUTER

Бренд: Scania Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды