PREVOST X3-45 COMMUTER Скачать руководство пользователя | Manualshive

Страница: 76 / 549

background image

SECTION 04: EXHAUST AND AFTERTREATMENT SYSTEM

12

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version – Rev.2 April 2016)

CAUTION

Protect filter area in the housing from
contamination.



Replace the filter element (a) and the

equalizing element (b).

CAUTION

The sealing surfaces on the housing must be
clean. No contamination or particles
acceptable.



Install filter cover. Torque to 16.5 lbf-ft.

CAUTION

It must be checked if there are cracks around
the area of the filter cover. No cracks in the
material are allowed. If there are cracks in the
housing, the entire Supply Module must be
replaced! If there are cracks in the filter cover,
the filter cover must be replaced.

MAINTENANCE

Replace pump assembly filter element after
the first 100,000 miles and then every
150,000 miles.

6.

AFTERTREATMENT FUEL INJECTOR

Proper functioning of the aftertreatment fuel
injector a.k.a. aftertreatment hydrocarbon
injector (AHI) is required in order to obtain
efficient regeneration process of the DPF.
Clogged aftertreatment fuel injector will result in
clogged DPF.

In addition to the activation of the CHECK
telltale, emission of diagnostic troubleshooting
codes (DTC) by the engine ECM (MID128) will
indicate malfunction of the aftertreatment system
and/or aftertreatment fuel injector. DTC may be
accessed through the Driver Information
Display. Select DIAGNOSTICS menu then
FAULT DIAGNOSTICS and ENGINE ECU
submenus.

Check status of the aftertreatment system
through the Driver Information Display. Select
AFTERTREATMENT menu then ATS STATUS.
Then check the DPF soot level with SOOT
LEVEL GAUGE.

6.1 REPLACEMENT

1. Remove fastener and p-clamp securing the

line to the mounting bracket on the diffuser
pipe.

WARNING

Fuel leaked or spilled onto hot surfaces or
electrical components can cause a fire and
result in component damage and serious
personal injury.

2. Disconnect the line from the aftertreatment

hydrocarbon injector fitting. Collect any
residual fuel that might be in the line in a
suitable container.

CAUTION

Do not kink the line. Kinking the line may
result in leakage.

«
...
74
75
76
77
78
...
»

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X3-45 COMMUTER

Zero Emission City Bus

Бренд: BCI Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды