PREVOST X3-45 COMMUTER Скачать руководство пользователя | Manualshive

Страница: 395 / 549

background image

SECTION 18: BODY

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version – Rev.2 April 2016)

25

position which engages a latch on the entrance
door, holding the door positively closed.

Emergency exit valve, which opens the air valve
circuit should be used only in emergencies, or
when the door control system does not function
properly.

Refer to the air system schematic diagram and
to page 29.1 of the wiring diagram.



Operation

Lock or unlock the bi-fold entrance door from
outside the vehicle by turning the key in the door
lock (counterclockwise to lock, clockwise to
unlock). The entrance door can be unlocked
from the inside using the small lever located on
the door.

The air-operated door is controlled from inside
the coach by two push-button switches located
on the R.H. dashboard.

FIGURE 21: ENTRANCE DOOR OPERATING BUTTONS

06464

From the inside, open the door by pressing the
door opening switch (L.H. button) on the R.H.
dashboard panel. The door will open to full open
position within 5 seconds.

Close by pressing and holding the door closing
switch (R.H. button) on the dashboard. If the
closing switch is released before the door is fully
closed, the door will stop in that position.

FIGURE 22: ENTRANCE DOOR CONTROL SWITCH

18599

Opening and closing of the door from outside
the coach is accomplished by a momentary
toggle switch located under the front R.H. side
marker light (Figure 22).

To close the door, the switch must be pushed
towards the rear of the coach and held in
position until the door has completed its
movement. The door can be closed to any
position by releasing the switch (or button, if
inside) when the desired position is attained.
However, the door is not locked in any position
other than fully closed. The door can then be
closed further by pushing or pulling on the door.

To open the door, the switch must be pushed
towards the front of the coach and held in
position. When the door reaches the fully
opened position, the system will keep pressure
in the cylinder locking the door in that position.

«
...
393
394
395
396
397
...
»

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X3-45 COMMUTER

Бренд: PREVOST Страницы: 258

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды