PREVOST X3-45 COMMUTER страница 416 Скачать руководство пользователя

Страница: 416 / 549

SECTION 18: BODY

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version – Rev.2 April 2016)

The small door has a piano hinge on its lower
edge.

1. Install only two of the mounting screws, at

each end to adjust the door.

2. Close door and adjust in opening. A 1mm

maximum difference between left and
right measured gap is accepted.

3. Door should close flush with the larger

door panel. Maximum flatness deviation
within 1mm.

4. Install the remaining screws and seal with

liquid Teflon #680098.



WCL Cassette Door latch adjustment

To allow adjustment of the latch mechanism,
lightly tighten the retaining hardware on
receptacle and striker support (arrows).

1. Place centering tool G34148_500 in the

receptacle cavity.

2. Close the door to center the latch mecha-

nism.

3. Tighten

screws

4. Check that the door swings freely and

closes properly without interference or
excessive force

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Похожие инструкции для X3-45 COMMUTER

Бренды по названию

Популярные бренды

PREVOST X3-45 COMMUTER, Руководство по обслуживанию

Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Похожие инструкции для X3-45 COMMUTER

Бренды по названию

Популярные бренды