PREVOST X3-45 COMMUTER страница 400 Скачать руководство пользователя

Страница: 400 / 549

SECTION 18: BODY

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version – Rev.2 April 2016)



From inside the door, apply some Sika

252 at the corners of window wiper.



Apply some #680066 glue inside finishing

panel groove and fix power window wiper.

NOTE

Anti-friction side must be on glass side.



Discard waste according to applicable

environmental regulations, use dangerous
waste containers.

Electrical Power Window



Insert 2 seals in the window frame.



Apply some #680066 glue at the intersec-

tion of the 2 seals and also sparingly in
order to fix the seal to the window frame.



Clean window using window cleaner.



Insert window into frame.



Secure window pane to raising

mechanism.



Adjust window travel (6±3mm above

window wiper).

Driver’s Window Gutter



Dry fit the gutter on the vehicle. If required,

straighten up gutter using a hammer and a
wooden block.

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Похожие инструкции для X3-45 COMMUTER

Бренды по названию

Популярные бренды

PREVOST X3-45 COMMUTER, Руководство по обслуживанию

Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Похожие инструкции для X3-45 COMMUTER

Бренды по названию

Популярные бренды