PREVOST X3-45 COMMUTER Скачать руководство пользователя страница 96

Страница: 96 / 549

SECTION 05: COOLING SYSTEM

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version – Rev.2 April 2016)

8. Open radiator door to access radiator

assembly. Unfasten upper arm assembly.

9. Remove radiator sealing frame.

FIGURE 20: RADIATOR SEALING FRAME

10. Remove clamps and then break hoses from

the front coolant and charge air pipes
(Figure 21).

FIGURE 21: RADIATOR & CHARGE AIR COOLER HOSE
CLAMPS

11. Remove rear coolant and charge air hose

clamps then break hoses loose.

12.

Remove the upper radiator assembly
support bracket (Figure 22).

FIGURE 22: UPPER SUPPORT BRACKET & TUBE
PROTECTOR

13. Remove the lower radiator assembly tube

protector from the lower section (Figure 22).

14.

Remove all lower radiator assembly
mounting fasteners.

FIGURE 23: RADIATOR ASSEMBLY LOWER MOUNTING
FASTENERS

15.

Cut cable tie and disconnect electrical
connector from fan clutch. Remove fan drive
shaft fasteners at the gear box.

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Бренды по названию

Популярные бренды

PREVOST X3-45 COMMUTER, Руководство по обслуживанию

Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Бренды по названию

Популярные бренды