PREVOST X3-45 COMMUTER Скачать руководство пользователя | Manualshive

Страница: 345 / 549

background image

SECTION 16: SUSPENSION

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Section 16 revised April 2019)

3

1. DESCRIPTION

The vehicle is provided with an air suspension
system. The system consists of air springs,
height control valves, radius rods, sway bars,
tripod and shock absorbers (Figure 1 to Figure
6). The system operation is fully automatic and
maintains a constant vehicle height regardless
of load, or load distribution.

The vehicle is also equipped with a front
kneeling system.

2. FRONT I-BEAM AXLE SUSPENSION

FIGURE 1: FRONT I-BEAM AXLE SUSPENSION

16105

2.1 AIR

SPRINGS

The air springs are made from a special
compound rubber molded to the proper contour
and dimensions. The entire vertical load of the
vehicle is supported by these springs. Each of
the three axles is provided with air springs that
are attached to the subframe and to the axles.

2.1.1

Inspection

1. Check operation of bellows.

2. Visually inspect bellows for evidence of

cracks, punctures, deterioration, or chafing.
Replace the bellows if any damage is
evident.

3. With the primary air system at normal

operating pressure (95 - 125 psi (655 - 860
kPa)), coat all suspension air line
connections and bellows mounting areas
with a water and soap solution. Bubbles will
indicate an air leak, and none is
permissible. Repair or replace defective
parts.

FIGURE 2: AIR SPRING

16052

NOTE

If air spring is removed from vehicle, bellows
can be lightly inflated and submerged in water
to detect any leakage. If any leakage is
detected, replace bellows.

WARNING

To prevent personal injury, do not apply more
than 10 psi (69 kPa) of air pressure to the
uninstalled air spring.

2.1.2

Removal

NOTE

Front suspension air springs can be removed

without removing the entire axle assembly.

1. Safely support vehicle at the recommended

body jacking points. To gain access to a

given air spring, the corresponding wheel

can be removed as follows:

a) Jack vehicle until the tire clears the

ground, and place safety supports

underneath body.

CAUTION

Only the recommended jacking points must be

used as outlined in Section 18, “Body”.

b) Support the axle with a suitable

hydraulic floor jack at the

recommended jacking points. Make

sure that the measurement between
the air spring mounting plates is

greater than the normal clearance

(normal ride height).

c) Remove

wheel.

«
...
343
344
345
346
347
...
»

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X3-45 COMMUTER

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды