PREVOST X3-45 COMMUTER Скачать руководство пользователя | Manualshive

Страница: 71 / 549

background image

SECTION 04: EXHAUST AND AFTERTREATMENT SYSTEM

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version – Rev.2 April 2016)

7

WARNING

Due to the heavy load of the radiator assembly,
it must be adequately supported before
attempting to remove it.



Safely support catalytic converter from the

top.



Disconnect catalytic converter outlet NOx

sensor.



Remove clamps holding catalytic converter

then lower.



Remove or disconnect any piece of

equipment or component that might be in
the way or that might prevent removing the
catalytic converter.

Procedure # 2



Set the starter selector switch to the

OFF

position.



Shut off the heater line shut-off valves.



Remove DOC and DPF assembly (Refer to
paragraph 2.1 in this Section).



Remove pipe connecting DOC & DPF

assembly to catalytic converter.



Using the quick-connect drain hose, drain

the engine cooling system. Refer to Section
05, COOLING under "DRAINING COOLING
SYSTEM".

CAUTION

Tag hoses and cables for identification before
disconnecting in order to facilitate re-
installation. Plug all openings to prevent dirt
from entering the system.



Disconnect and remove section of coolant

pipe assembly mounted between the
radiator outlet and the water pump inlet.



Disconnect and remove a section of coolant
pipe assembly mounted between the
thermostat housing and the radiator inlet.



Disconnect and remove a section of air

intake duct mounted between the air cooler
outlet and the engine.



Remove coolant surge tank.



Release tension from drive belt (Refer to

paragraph 12.1 and 15.1 in Section 05:
Cooling System).



Cut cable ties and disconnect electrical

connector from fan clutch. Remove fan drive
shaft fasteners at the gear box.



Remove radiator fan drive mechanism

support.



Safely support catalytic converter from the

top.



Disconnect catalytic converter outlet NOx

sensor.



Remove clamps holding catalytic converter

then lower.



Remove or disconnect any piece of

equipment or component that might be in
the way or that might prevent removing the
catalytic converter.

3.2 ASSEMBLING CATALYTIC CONVERTER

Before removing



Mark, with a vertical line the angular position
of the lower (both sides) and upper clamps
with regard to the clamps support located on
the catalytic converter.

Lower

Upper



Mark, with a vertical line the central position
of the lower and upper clamps with regard to

«
...
69
70
71
72
73
...
»

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X3-45 COMMUTER

effeff ePED Hi-O Technology Bus

Бренд: Assa Abloy Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды