manualshive.com logo in svg

PREVOST X3-45 COMMUTER, Руководство по обслуживанию

Поделиться
Скачать
PREVOST X3-45 COMMUTER Скачать руководство пользователя страница 367

 

<QF7720955 rev 2> 

 

MAINTENANCE

INFORMATION

 

MI15-41 

DATE : 

AUGUST 2015 

SECTION : 18 - Body 

SUBJECT 

:  CRACKING OF POLYCARBONATE TAILLIGHTS 

CAUSED BY INAPPROPRIATE CLEANING PRODUCTS

 

 

 

 

APPLICATION 

Model 

VIN 

 

ALL MODELS 

DESCRIPTION 

Prevost would like to remind its customers that only 

cleaning products designed for external washing 

of vehicles

 should be used for exterior vehicle wash and in particular, for the washing of polycarbonate 

taillights. 

POLYCARBONATE CRACKING 

Degreasers designed to clean motors 

must not be used

 to clean the engine compartment door. These 

products are not compatible with polycarbonate. They cause cracking of the polycarbonate taillights 
housing and cracking of the bosses in which the mounting threaded rods are inserted (figures 2 & 3). 

CLEANING PRODUCT COMPATIBLE WITH POLYCARBONATE 

Cleaning products designed for external washing of vehicles shall be used to clean your vehicle. Prevost 
suggests a high PH cleaner compatible with polycarbonate. See the description of the product in the 
following table 

Part No 

Description 

Qty 

686037 

EXTERIOR CLEANER (BODY) 

1 gallon / 4 liters 

686036 

EXTERIOR CLEANER (BODY) 

5.28 gallons / 20 liters 

685841 

EXTERIOR CLEANER (BODY) 

55 gallons / 210 liters 

 

 

NOTE 
Material can be obtained through regular channels.

 

 

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды