PREVOST X3-45 COMMUTER Скачать руководство пользователя | Manualshive

Страница: 391 / 549

background image

SECTION 18: BODY

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version – Rev.2 April 2016)

21

FIGURE 13: BUMPER HINGE BOLTS

18704

15.1.2 HEADLIGHTS

Refer to Paragraph Headlights, included in
Section 06: Electrical of the Maintenance
Manual for complete information on headlights.

15.1.3 REAR VIEW MIRRORS (ROSCO)

Your vehicle is equipped with two Rosco exterior
mirrors.

The mirrors can easily be adjusted by using the
remote controls located on the L.H. side control
panel. The mirrors have easy to replace glass in
case of breakage. Remote control motors can
also be replaced.

FIGURE 14: L/H REAR VIEW MIRROR (ROSCO)

18398B



Adjustment

At the base of the mirror arm, loosen the
mounting bolt to swing arm in or out.

To pivot the mirror head, loosen the setscrews
on each side of the ball stub at the base of the
mirror head to facilitate the adjustment.



Disassembly

At end of mirror arm, loosen the setscrews to
relieve tension on the ball stem. Remove the ball
stem from the arm.

Remove the four screws fastening the mirror
arm base to the coach.



Assembly

Mount the mirror arm base to the coach. Insert
the ball stem into the mirror arm and tighten the
socket setscrews.

NOTE

Position the ball cup halves so the joint
between them lies on the centerline of the
arm. Ensure that the setscrews are not on the
joint between the cup halves.



Remote Controlled Rear View Mirrors

The remote controlled external rear view mirrors
attach to support arms using a pivot collar
secured by setscrews. Loosening the setscrews
allows the whole head assembly to turn on the
support arm for initial adjustment. A mounting
bolt and washer hold the arm support to the
mounting bracket. The arm support can be
moved to position the mirror head into or away
from the coach body.



Mirror

Control

The remote control pointer knob(s) for the
mirrors is (are) mounted on the L.H. side control
panel. The harness to the mirror head runs
through the arm support. The remote motor is
mounted to the mirror head behind the mirror
glass.

Choose the side to be adjusted by pressing
the “L” (left) or “R” (right) button on the
control pad. The flat mirror is then adjusted
by pressing the “upper” button and the
convex mirror by pressing the “lower”
button. The selected mirror can now be
adjusted left to right or up and down by
using the arrow keys on the control pad. The
R/H side round mirror is non-adjustable.

«
...
389
390
391
392
393
...
»

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X3-45 COMMUTER

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды