PREVOST X3-45 COMMUTER страница 2 Скачать руководство пользователя

Страница: 2 / 549

PA1605 November 2014 (first release)

Featuring:



GHG14 regulations engine



ZF A-132 Drive Axle

REVISION

DESCRIPTION

DATE

- Sec 22: Heating and Air Conditioning updated.

- Sec 13: Wheels, Hubs and Tires: updated to reflect wheel dimensions on new build; Drive
axle hub updated to “ZF” design.

Feb. 2015

- Addition of “Change Log” table at the end of each section.
- Tightening torques changed in Section 16. Refer to Section 16 Change Log.

April 2016

- Addition of steering play inspection. See Section 14 & lubrication and SERVICING
SCHEDULE.

August 2016

- Fuel tank strap torque was 60 lb-ft, is 20 lb-ft.

October 2016

- Section 24a LUBRICATION AND SERVICING SCHEDULE updated.

June 2017

- Section 03: FUEL. Fuel tank yearly inspection added.
- Section 24a lubrication and servicing schedule updated.

May 2018

- Section 24a LUBRICATION AND SERVICING SCHEDULE updated.

March 2019

- Section 16 SUSPENSION revised.

April 2019

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Похожие инструкции для X3-45 COMMUTER

Бренды по названию

Популярные бренды

PREVOST X3-45 COMMUTER, Руководство по обслуживанию

Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Похожие инструкции для X3-45 COMMUTER

Бренды по названию

Популярные бренды