PREVOST X3-45 COMMUTER Скачать руководство пользователя страница 508

Страница: 508 / 549

SECTION 22: HEATING AND AIR CONDITIONING

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version – Rev.2 April 2016)

CAUTION

Be careful not to damage the machined faces
while the valve is apart.

7.9.5 Valve

Reassembly

1. Place the seat disc into the valve body with

the smaller diameter end facing up.

2. Place the enclosing tube gasket onto the

valve body above the threads.

3. Hold the plunger with one hand so that the

pointed end is resting in the pilot port of the
disk. Make sure the small spring is in place
on the top of the plunger.

4. With the other hand, place the enclosing

tube over the plunger, making sure the
enclosing tube gasket is in position.

5. Put back the enclosing tube locknut and

tighten

20-40 lbf-ft

. Do not over tighten.

6. Put back manual lift stem. Tighten lift stem

assembly and seal cap to

11 lbf-ft

7. Place the coil assembly.

FIGURE 43: TYPICAL REFRIGERANT SOLENOID VALVE

22044

FIGURE 44: REFRIGERANT SOLENOID VALVE

22044

CAUTION

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Бренды по названию

Популярные бренды

PREVOST X3-45 COMMUTER, Руководство по обслуживанию

Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Бренды по названию

Популярные бренды