PREVOST X3-45 COMMUTER Скачать руководство пользователя страница 155

Страница: 155 / 549

ELECTRICAL CONNECTORS PROTECTION

PROCEDURE NO SAV00002E

NOVEMBER 2009

REVISION 02

Page 1 of 4

Kent Sealer

680324

Sprayed sealer. It is used for structure ground connections. It prevents
corrosion and ensures maximum contact

Refer to table for proper use.

Apply this product once installation is finished.

Warning: It is very important to be in a well ventilated area when applying
this product.

Nyogel Grease

3 Oz. tube: 681095

Container 500g: 683409

Grease-type product.

It is used to facilitate connectors or terminals insertion.

Refer to table for proper use of Nyogel grease.

It is preferable to apply Nyogel into the female part of connector.

Apply this product as the last assembling operation.

“Color Guard” black rubber coating

684013

This product may be applied with a brush.

It is used for structure ground connections or other connections that will most
likely not be disconnected later on.

Apply this product once installation is finished.

Warning : Wear goggles and rubber gloves.

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Бренды по названию

Популярные бренды

PREVOST X3-45 COMMUTER, Руководство по обслуживанию

Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Бренды по названию

Популярные бренды