PREVOST X3-45 COMMUTER Скачать руководство пользователя страница 420

Страница: 420 / 549

SECTION 18: BODY

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version – Rev.2 April 2016)

Paint Code: #J4099U

Major Repair (Hole)

Chamfer the whole perimeter of the damaged
area. If applicable, remove loose covering.
Remove dust and particles.

Cover and protect damaged area surroundings.

Using a plastic spatula, apply some Sika 221
grey onto the damaged area.

Remove masking tape and protection around
damaged area.

Spray pure water onto Sika. Use a floor sample
to create some texture onto the adhesive.

If possible spray some more water onto the
adhesive to accelerate curing.

Allow drying for at least

2 hours

then repaint as

per paragraph: Minor Repair.



Baggage Compartment Floor Installation

Preparation and Installation

Clean baggage compartment support structure
using anti-silicone.

Glue spacers (790392) about 16-inch apart.

Rear baggage compartment without WCL.

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Бренды по названию

Популярные бренды

PREVOST X3-45 COMMUTER, Руководство по обслуживанию

Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Бренды по названию

Популярные бренды