PREVOST X3-45 COMMUTER Скачать руководство пользователя страница 414

Страница: 414 / 549

SECTION 18: BODY

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version – Rev.2 April 2016)



Adjust door position and evenness with

reference to adjacent panels and doors.

NOTE

Adjustment is made by moving IN or OUT the
lock plates. Adjust one corner at a time.



Check handle adjustment. Handle must

remain tight against its plastic housing.

NOTE

Adjustment is made by moving UP or DOWN
the lock plates.



Open baggage compartment door and

adjust using the cylinder mounting block.



Door should be adjusted in reference to

neighboring doors.



Target is to have 5 ½” (140mm) from bus

body panel to door panel and +/- 2mm
vertically between doors.

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Бренды по названию

Популярные бренды

PREVOST X3-45 COMMUTER, Руководство по обслуживанию

Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Бренды по названию

Популярные бренды