PREVOST X3-45 COMMUTER Скачать руководство пользователя | Manualshive

Страница: 151 / 549

background image

SECTION 06: ELECTRICAL

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version) – Sec 06 revised June 2017

47

2. Disconnect the electric cable from the

switch.

3. To install a new switch, reverse the

procedure (Figure 49).

Note

Switches are lighted by the use of led. When
lighting on a switch fails, replace defective
switch as a unit.

FIGURE 49: DASHBOARD ROCKER SWITCH

06321

11.1.2 Telltale light replacement

Telltale module is non-serviceable and must be
replaced as a unit.

1. Unscrew and remove the top dashboard

panel.

2. Remove the telltale back wire electric

connectors.

3. Unscrew and remove the telltale module.

4. To replace the telltale module, reverse the

procedure.

11.1.3 Gauge light bulb replacement

1. For any gauge light bulb replacement, the

dashboard panel must be removed in order
to have access to the rear of gauges.

2. Remove bulb socket from the gauge, turn

the defective bulb counterclockwise and pull
it out of the gauge.

3. Push a new bulb and socket asm and turn

clockwise to lock in place.

4. Replace the rear dashboard housing.

11.2 STEPWELL

LIGHTS

Two stepwell lights are illuminated when the
door opening system is activated.

11.2.1 Bulb removal and replacement

Proceed as follows to replace a defective bulb:

1. Unscrew the two phillips-head screws

retaining the lens to the wall, and remove it.

2. With the light lens removed, pull bulb from

the lamp while applying lateral pressure.

3. Install the new bulb into the lamp.

4. Position the light lens and install it.

11.3 DRIVER’S AREA LIGHTS

Two halogen ceiling lights are installed over the
stepwell and the driver’s area. These lights are
frequently used for night-time operation when
passengers board or leave coach.

11.3.1 Bulb removal and replacement

1. Unsnap the lamp with a flat head

screwdriver and remove it.

2. Pull the defective bulb out of the socket.

3. Install the new bulb by pushing it in position.

4. Replace the lamp by snapping it back in

place.

Caution

Do not touch halogen bulbs with bare hands
as natural oils on skin will shorten bulb life
span.

11.3.2 Engine Compartment Lighting

A switch located on the upper right corner of the
rear start panel can be used to actuate the
engine compartment led lights.

FIGURE 50: ENGINE COMPARTMENT LIGHT

«
...
149
150
151
152
153
...
»

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X3-45 COMMUTER

Бренд: GMC Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды