PREVOST X3-45 COMMUTER страница 274 Скачать руководство пользователя | Manualshive

Страница: 274 / 549

background image

SECTION 12: BRAKE AND AIR SYSTEM

4

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version – Rev.2 April 2016)

1. AIR

SYSTEM

The basic air system consists of an air
compressor, reservoirs, valves, filters and
interconnecting lines and hoses. It provides a
means for braking; operating controls and
accessories, and suspension (refer to Section
16,

"Suspension"

, for complete information on

suspension description and maintenance). An
air system schematic diagram is annexed in the
technical publications box provided with the
vehicle for better understanding of the system.

2. BRAKES

This vehicle uses both the service brake and
emergency/parking brake. The service brake air
system is divided into two independent circuits
to isolate front brakes from rear brakes, thus
providing safe braking in the event that one
circuit fails. Front axle brakes operate from the
secondary air system, while brakes on both the
drive axle and tag axle operate from the primary
air system.

NOTE

The tag axle service brake operates only when
the axle is in normal ride position (loaded and
down).

Furthermore, the brake application or release,
which is speed up by a pneumatic relay valve,
will start with the rear axles and will be followed
by the front axle, thus providing uniform braking
on a slippery road. The vehicle is also equipped
with an Anti-Lock Braking System (ABS), which is
detailed later in this section.
The drive axle is provided with spring-loaded
emergency/parking brakes, which are applied
automatically whenever the control valve supply
pressure drops below 60 psi (414 kPa).

FIGURE 1: I-BEAM FRONT SUSPENSION AIR RESERVOIRS LOCATION

12213

3. AIR

RESERVOIRS

The air coming from the compressor is first
forwarded to the ping tank, then to the Haldex
condenser-separator, the air dryer, the wet air
tank, the primary (for the primary brake system),
secondary (for the secondary brake system),
and accessory (for the pneumatic accessories)
air tanks (Figure 1).

Two additional air reservoirs are installed on the
vehicle: the kneeling air tank and the parking
brakes overrule air tank.

3.1

WET TANK AUTOMATIC DRAIN

VALVE
The wet tank automatic drain valve (Figure 2) is
designed to remove liquids from the wet tank
each time the brake is applied as the solenoid is

connected to the stop light circuit. A built-in
heater prevents freeze-ups and keeps the air
system clean in all temperature.

3.1.1 Installation

1. Make sure that there is no pressure in the

wet tank (emptied tank).

2. Fit the automatic drain valve to the wet tank.

Tighten valve finger tight and then tighten an
additional 1 ½ turns, do not over tighten.

3. Connect the power cable to the valve

connector.

4. Charge the air system and make sure there

is no leakage. Also check functioning of the
drain valve by applying the service brake.

«
...
272
273
274
275
276
...
»

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X3-45 COMMUTER

Бренд: MARCOPOLO Страницы: 168

Lion's Intercity LE

Бренд: Man Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды